906e2a1b99
Device specifications:
======================
* Qualcomm/Atheros AR9344
* 128 MB of RAM
* 16 MB of SPI NOR flash
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4/5 GHz Wi-Fi
* 4x GPIO-LEDs (1x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* 2x fast ethernet
- lan1
+ builtin switch port 1
+ used as WAN interface
- lan2
+ builtin switch port 2
+ used as LAN interface
* 9-30V DC
* external antennas
Flashing instructions:
======================
Log in to https://192.168.127.253/
Username: admin
Password: moxa
Open Maintenance > Firmware Upgrade and install the factory image.
Serial console access:
======================
Connect a RS232-USB converter to the maintenance port.
Pinout: (reset button left) [GND] [NC] [RX] [TX]
Firmware Recovery:
==================
When the WLAN and SYS LEDs are flashing, the device is in recovery mode.
Serial console access is required to proceed with recovery.
Download the original image from MOXA and rename it to 'awk-1137c.rom'.
Set up a TFTP server at 192.168.127.1 and connect to a lan port.
Follow the instructions on the serial console to start the recovery.
Signed-off-by: Maximilian Martin <mm@simonwunderlich.de>
167 lines
3.8 KiB
Bash
167 lines
3.8 KiB
Bash
#!/bin/sh
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions/caldata.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"ath9k-eeprom-ahb-18100000.wmac.bin")
|
|
case $board in
|
|
8dev,lima)
|
|
caldata_extract "art" 0x1000 0x800
|
|
;;
|
|
aruba,ap-115)
|
|
caldata_extract "oemdata" 0x1000 0x440
|
|
;;
|
|
asus,pl-ac56|\
|
|
asus,rp-ac51|\
|
|
asus,rp-ac66)
|
|
caldata_extract "art" 0x1000 0x440
|
|
;;
|
|
avm,fritz1750e|\
|
|
avm,fritz4020|\
|
|
avm,fritz450e|\
|
|
avm,fritzdvbc)
|
|
caldata_extract_reverse "urlader" 0x1541 0x440
|
|
;;
|
|
dlink,dir-505)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_text "mac" 0x4)
|
|
;;
|
|
dlink,dir-842-c1|\
|
|
dlink,dir-842-c2|\
|
|
dlink,dir-842-c3|\
|
|
nec,wf1200cr|\
|
|
nec,wg1200cr|\
|
|
wd,mynet-n600|\
|
|
wd,mynet-n750)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii devdata "wlan24mac")
|
|
;;
|
|
engenius,ecb1200|\
|
|
engenius,ecb1750)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env athaddr) 1)
|
|
;;
|
|
enterasys,ws-ap3705i)
|
|
caldata_extract "calibrate" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env0 RADIOADDR1)
|
|
;;
|
|
extreme-networks,ws-ap3805i)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii cfg1 RADIOADDR1)
|
|
;;
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr|\
|
|
iodata,wn-ac1600dgr2|\
|
|
iodata,wn-ag300dgr|\
|
|
sitecom,wlr-7100|\
|
|
sitecom,wlr-8100)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
;;
|
|
moxa,awk-1137c)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env mac_addr)
|
|
;;
|
|
nec,wg800hp)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_text board_data 0x680)
|
|
;;
|
|
qihoo,c301)
|
|
caldata_extract "radiocfg" 0x1000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii devdata "wlan24mac")
|
|
;;
|
|
tplink,deco-s4-v2)
|
|
caldata_extract "art" 0x1000 0x440
|
|
base_mac=$(mtd_get_mac_encrypted_deco $(find_mtd_part config))
|
|
ath9k_patch_mac $(macaddr_add $base_mac 1)
|
|
;;
|
|
*)
|
|
caldata_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
"ath9k-eeprom-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
aruba,ap-115)
|
|
caldata_extract "oemdata" 0x5000 0x440
|
|
;;
|
|
avm,fritz300e)
|
|
caldata_extract_reverse "urloader" 0x1541 0x440
|
|
;;
|
|
buffalo,wzr-hp-g450h|\
|
|
pcs,cap324)
|
|
caldata_extract "art" 0x1000 0x440
|
|
;;
|
|
dlink,dir-825-c1|\
|
|
dlink,dir-835-a1)
|
|
caldata_extract "art" 0x5000 0x440
|
|
ath9k_patch_mac $(macaddr_add $(mtd_get_mac_text "mac" 0x18) 1)
|
|
;;
|
|
enterasys,ws-ap3705i)
|
|
caldata_extract "calibrate" 0x5000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env0 RADIOADDR0)
|
|
;;
|
|
meraki,mr12)
|
|
caldata_extract "art" 0x11000 0xeb8
|
|
;;
|
|
netgear,wnr2200-8m|\
|
|
netgear,wnr2200-16m|\
|
|
tplink,tl-wr842n-v1)
|
|
caldata_extract "art" 0x1000 0x3e0
|
|
;;
|
|
wd,mynet-n600|\
|
|
wd,mynet-n750)
|
|
caldata_extract "art" 0x5000 0x440
|
|
ath9k_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
|
|
;;
|
|
wd,mynet-wifi-rangeextender)
|
|
caldata_extract "art" 0x1000 0x440
|
|
ath9k_patch_mac $(nvram get wl0_hwaddr)
|
|
;;
|
|
*)
|
|
caldata_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
"ath9k-eeprom-pci-0000:00:11.0.bin")
|
|
case $board in
|
|
buffalo,wzr-600dhp|\
|
|
buffalo,wzr-hp-ag300h)
|
|
caldata_extract "art" 0x1000 0xeb8
|
|
;;
|
|
trendnet,tew-673gru)
|
|
caldata_extract "caldata" 0x1000 0xeb8
|
|
ath9k_patch_mac_crc $(mtd_get_mac_text "caldata" 0xffa0) 0x20c
|
|
;;
|
|
meraki,mr16)
|
|
caldata_extract "art" 0x11000 0xeb8
|
|
;;
|
|
*)
|
|
caldata_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
"ath9k-eeprom-pci-0000:00:12.0.bin")
|
|
case $board in
|
|
buffalo,wzr-600dhp|\
|
|
buffalo,wzr-hp-ag300h)
|
|
caldata_extract "art" 0x5000 0xeb8
|
|
;;
|
|
trendnet,tew-673gru)
|
|
caldata_extract "caldata" 0x5000 0xeb8
|
|
ath9k_patch_mac_crc $(macaddr_add $(mtd_get_mac_text "caldata" 0xffb4) 1) 0x20c
|
|
;;
|
|
meraki,mr16)
|
|
caldata_extract "art" 0x15000 0xeb8
|
|
;;
|
|
*)
|
|
caldata_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
esac
|