These intervals are allocatable immediately after splitting, but they may be
evicted because of later splitting. This is rare, but when it happens they
should be split again.
The remainder intervals that cannot be allocated after splitting still move
directly to spilling.
SplitEditor::finish can optionally provide a mapping from new live intervals
back to the original interval indexes returned by openIntv().
Each original interval index can map to multiple new intervals after connected
components have been separated. Dead code elimination may also add existing
intervals to the list.
The reverse mapping allows the SplitEditor client to treat the new intervals
differently depending on the split region they came from.
llvm-svn: 129925
On the x86-64 and thumb2 targets, some registers are more expensive to encode
than others in the same register class.
Add a CostPerUse field to the TableGen register description, and make it
available from TRI->getCostPerUse. This represents the cost of a REX prefix or a
32-bit instruction encoding required by choosing a high register.
Teach the greedy register allocator to prefer cheap registers for busy live
ranges (as indicated by spill weight).
llvm-svn: 129864
This merges the behavior of splitSingleBlocks into splitAroundRegion, so the
RS_Region and RS_Block register stages can be coalesced. That means the leftover
intervals after region splitting go directly to spilling instead of a second
pass of per-block splitting.
llvm-svn: 129379
It is common for large live ranges to have few basic blocks with register uses
and many live-through blocks without any uses. This approach grows the Hopfield
network incrementally around the use blocks, completely avoiding checking
interference for some through blocks.
llvm-svn: 129188
About 90% of the relevant blocks are live-through without uses, and the only
information required about them is their number. This saves memory and enables
later optimizations that need to look at only the use-blocks.
llvm-svn: 128985
When the greedy register allocator is splitting multiple global live ranges, it
tends to look at the same interference data many times. The InterferenceCache
class caches queries for unaltered LiveIntervalUnions.
llvm-svn: 128764
When DCE clones a live range because it separates into connected components,
make sure that the clones enter the same register allocator stage as the
register they were cloned from.
For instance, clones may be split even when they where created during spilling.
Other registers created during spilling are not candidates for splitting or even
(re-)spilling.
llvm-svn: 128524
The reassignment phase was able to move interference with a higher spill weight,
but it didn't happen very often and it was fairly expensive.
The existing interference eviction picks up the slack.
llvm-svn: 128397
This simplifies the code and makes it faster too.
The interference patterns are saved for each candidate register. It will be
reused for actually executing the split. Work in progress.
llvm-svn: 127054
This effectively disables the 'turbo' functionality of the greedy register
allocator where all new live ranges created by splitting would be reconsidered
as if they were originals.
There are two reasons for doing this, 1. It guarantees that the algorithm
terminates. Early versions were prone to infinite looping in certain corner
cases. 2. It is a 2x speedup. We can skip a lot of unnecessary interference
checks that won't lead to good splitting anyway.
The problem is that region splitting only gets one shot, so it should probably
be changed to target multiple physical registers at once.
Local live range splitting is still 'turbo' enabled. It only accounts for a
small fraction of compile time, so it is probably not necessary to do anything
about that.
llvm-svn: 126781
New live ranges are assigned in long -> short order, but live ranges that have
been evicted at least once are deferred and assigned in short -> long order.
Also disable splitting and spilling for live ranges seen for the first time.
The intention is to create a realistic interference pattern from the heavy live
ranges before starting splitting and spilling around it.
llvm-svn: 126451
When a large live range is evicted, it will usually be split when it comes
around again. By deferring evicted live ranges, the splitting happens at a time
when the interference pattern is more realistic. This prevents repeated
splitting and evictions.
llvm-svn: 126282
Use interval sizes instead of spill weights to determine if it is legal to evict
interference. A smaller interval can evict interference if all interfering live
ranges are larger.
Allow multiple interferences to be evicted as along as they are all larger than
the live range being allocated.
Spill weights are still used to select the preferred eviction candidate.
llvm-svn: 126276
This is based on the observation that long live ranges are more difficult to
allocate, so there is a better chance of solving the puzzle by handling the big
pieces first. The allocator will evict and split long alive ranges when they get
in the way.
RABasic is still using spill weights for its priority queue, so the interface to
the queue has been virtualized.
llvm-svn: 126259
An original endpoint is an instruction that killed or defined the original live
range before any live ranges were split.
When splitting global live ranges, avoid creating local live ranges without any
original endpoints. We may still create global live ranges without original
endpoints, but such a range won't be split again, and live range splitting still
terminates.
llvm-svn: 126151
